Installed PERC management software afaapps and created simple mirror

Posted on August 18, 2009

Installed PERC management software afaapps and created simple mirror

I just installed Debian Lenny on a Dell 2650 with an OLD PERC 3 RAID controller.

I then installed the afaapps package from Dell’s website (http://support.us.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R85529&formatcnt=1&libid=0&fileid=112003)
Use this link or just search for ‘afaapps’ under the Drivers and Downloads section of the Dell support site.

After extracting the rpm from the downloaded file I ran alien against the file to turn it into a debian file

#apt-get install alien
#alien -d –scripts afaapps-2.8-0.i386.rpm

Now just install theÂ created debian package

#dpkg -i afaapps_2.8-1_i386.deb

Now that you have installed the afacli you can run it at the command line prompt which will open theÂ PERC command line “FASTCMD>”
Then you’ll open / connect to the RAID controller using “open afa0”

#afacli
FASTCMD> open afa0
Executing: open “afa0”

A simple ‘disk list’ command to find out what your disk situation looks like

AFA0> disk list
Executing: disk list

B:ID:L Device Type Blocks Bytes/Block Usage Shared
—— ————– ——— ———– —————- ——
0:00:0 Disk 35566478Â 512 Initialized NO
0:01:0 Disk 287132440 512 Initialized NO
0:02:0 Disk 287132440 512 Initialized NO

you may have to initialize your disks by typeing ‘disk initialize 1’ and ‘disk initialize 2’ to make sure that the container can access them,Â you can see in my example above that my two disks are already initialized.

Now I will create a volume on disk 1 and mirror that disk to disk 2

AFA0> container create volume 1
AFA0> container create mirror 1 2

At the bottom of your screen you should see the status of the mirroring Job, something like.

Stat:OK!, Task:100, Func:MSC Ctr:1, State:RUN 16.2%

Once the job completes you can partition and format the disk. Check the label on the disk by running:

AFA0> container list
Executing: container list
Num Total Oth Chunk Scsi Partition
Label Type Size Ctr Size Usage B:ID:L Offset:Size
—– —— —— — —— ——- —— ————-
0 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

1 Mirror 136GB Valid 0:01:0 64.0KB: 136GB
/dev/sdb 0:04:0 64.0KB: 136GB

From this I can see that I will need to partition and format disk “/dev/sdb”

Have fun! And if I can help you on it let me know.

Adding Disk Space to an Array on a Dell PERC using AFACLI

Posted on July 23, 2009

Linux Server Administration Server Hardware

Adding Disk Space to an Array on a Dell PERC using AFACLI

This blog describes the commands necessary to add a disk to existing RAID V array in the case where you have an empty available slot where you can add a disk.
The actual manual for afacli can be found here:
http://docs.us.dell.com/support/edocs/storage/57kgr/cli/en/index.htm

Accessing the CLI from the UNIX Prompt

To access the CLI from the UNIX prompt, display a window and type afacli in any directory. The system displays the FASTCMD> prompt, which indicates you can now use CLI commands. The path in the startup file (.login or .cshrc) must include the directory where the software is installed for the command to work in any directory. See your UNIX documentation for information on setting up directory paths in the .login and .cshrc files.

To view all controllers use €˜controller list€™
To connect to the controller with the command line utility, execute:

FASTCMD> open afa0

AFA0>

To show the status of all disks in all arrays and get an overview of the disks in the RAID, execute €˜enclosure show status€™.

AFA0> enclosure show status

Executing: enclosure show status

Enclosure
ID (B:ID:L) UpTime D:H:M PowerCycle Interval Door Alarm
———– ————– ———- ——– ——– —–
0 0:06:0 0:00:00 0 10 UNLOCKED OFF

Enclosure
ID (B:ID:L) Fan Status
———– — ————-

Enclosure
ID (B:ID:L) Power State Status
———– —– ———— ——-

Enclosure
ID (B:ID:L) Slot scsiId Insert Status
———– —- —— ——- ——————————————
0 0:06:0   0   0:00:0     1   OK ACTIVATE
0 0:06:0   1   0:01:0     1   OK ACTIVATE
0 0:06:0   2   0:02:0     1   OK ACTIVATE
0 0:06:0   3   0:03:0     1   OK ACTIVATE
0 0:06:0   4   0:255:0     0   OK UNCONFIG EMPTY I/R READY NOTACTIVATE

Enclosure
ID (B:ID:L) Sensor Temperature Threshold Status
———– —— ———– ——— ——–
0 0:06:0 0 73 F 120 NORMAL
0 0:06:0 1 69 F 120 NORMAL

Above, there is no disk in slot 4, insert the disk again and execute the command again to see it again.

AFA0> enclosure show status
Executing: enclosure show status

Enclosure
ID (B:ID:L) UpTime D:H:M PowerCycle Interval Door Alarm
———– ————– ———- ——– ——– —–
0 0:06:0 0:00:00 0 10 UNLOCKED OFF

Enclosure
ID (B:ID:L) Fan Status
———– — ————-

Enclosure
ID (B:ID:L) Power State Status
———– —– ———— ——-

Enclosure
ID (B:ID:L) Sensor Temperature Threshold Status
———– —— ———– ——— ——–
0 0:06:0 0 73 F 120 NORMAL
0 0:06:0 1 73 F 120 NORMAL

You can see that the disk in slot 4 is waiting to be configured. lets take a look at the RAID V container that we are going to add the new disk to, execute “container list”

AFA0> container list
Executing: container list
Num          Total Oth Chunk          Scsi   Partition
Label Type   Size   Ctr Size   Usage   B:ID:L Offset:Size
—– —— —— — —— ——- —— ————-
0    RAID-5 101GB       64KB Valid   0:00:0 64.0KB:33.8GB
/dev/sda                                         0:01:0 64.0KB:33.8GB
0:02:0 64.0KB:33.8GB
0:03:0 64.0KB:33.8GB

Even though it is visible in the enclosure list above, you will need to execute a “controller rescan” to find the new disk.

AFA0> controller rescan
Executing: controller rescan

Now initialize the disk so it can be used.

AFA0> disk initialize 4
Executing: disk initialize (ID=4)

Finally you can add the disk to the container, you will simply run the container reconfigure command with the container number (in our case 0) and the device number (in our case 4)

AFA0> container reconfigure 0 4
Executing: container reconfigure 0 (ID=4)

Now, wait for the disk to rebuild. You can view the rebuild process with €˜task list€™.

AFA0> task list
Executing: task list

Controller Tasks

TaskId Function Done% Container State Specific1 Specific2
—— ——– ——- ——— —– ——— ———
101 Reconfg 8.4% 0 RUN 00000000 00000000

Also while adding a new disk to this array I found that the existing array was only using 25.6 GB of each disk and not the full 36 GB

I issued a “container reconfigure” command to utilize the more space on each disk

AFA0> container reconfigure /partition_size=36388763000 0
Executing: container reconfigure /partition_size=36,388,763,000 0